Except not because mine's silver. I've never seen another silver one.
He ran a bunch of pics of Rocky Mountain racers on their Edges back in the day and I was pretty happy to see they were all running Rock Shox Judy DH forks - just like mine. However, they also had Magura Raceline hydraulic brakes. Turns out, I have a set, so get comfy, this is going to take a while...
I had heard that setting them up can be a real battle - this was what Ali Clarkson says anyway. You should be watching him on YouTube as well. But, he never really said why, and in fact, I can't find anyone who says why, so, here's my guide explaining why it's a battle to set them up.
I was lulled into a false sense of security by the RaceLines, because I put them on my Rocky Experience, and it was a piece of cake. But we had many issues on the Edge, the first being that the rear wheel was dished poorly. You can see this in Plate 2. It was easy enough to shift it over though, and you can see in Plate 3, we now have even spacing for the pads on both sides.
But I've jumped way ahead here, as dishing the wheel was a secondary issue.
You can start with putting the left side on, tightening the 5mm bolt, and setting the height of the pad relative to the rim. Then, visible in Plate 4, you loosen the 4mm bolt above the pad, and put a 13mm wrench on the weird post that sticks out behind the brake. You can see this clearly in Plate 6. This post can be adjusted with the wrench to help set the distance from the pad to the rim. I think it also helps secure the brake against the frame so that it doesn't just push the body of the brake away from the rim rather than the pad into the rim.
This is now where we discover just what's so difficult about these brakes; you more or less need to adjust the height of the pad relative to the rim, the angle of the pad relative to the rim, and the distance of the pad from the rim all at the same time.
You can see in Plate 7 below, the black clamp that holds the 'caliper' in place, is split, so when you loosen it, you can move the caliper around inside the clamp. You also need to loosen the 4mm at the top of the clamp to do this, and that allow the entire brake to slide down, and the post to move around - and you end up having to set three vital parameters all at once.
So - we're all done now?
No. No we are not. We have to do the front, and there is a major problem. In Plate 6 you can see the entirety of the post that sticks out behind the brake is on the brake arch of the Judy, so you can't adjust it away from the rim enough. But that's where the spacers with the flat side and the set screw from Plate 1 come in. It occurred to me that they can go behind the brake, pushing it out enough to clear the arch.
As it happens, I watched a video on a vintage show in the UK that confirmed this. You can clearly see the spacer in Plate 7. So with the spacers in place, you can see in Plates 8 and 9, there is plenty of clearance for that post, allowing for the body of the brake to be moved away from the rim, and now we are done.
Except no we are not.
See that post in Plate 8? The one with the groove on the end that the flip lever bites into to lock the brake in place? Yeah, it's now sitting way too far in for the cam in the lever to grab. I found that a locking for a presta valve stem is a great match, except it sticks out too far and doesn't fit inside the brake. So I could try to file it down.
What I did is probably not all that good, but it seems to work so far. I backed out that post so that the cam does hit it and flipped the lever shut. Then I tightened that post until everything was snugged down.
It's dodgy because I know it's not designed for that, but, I'm not DH racing it. I'll probably barely ride it all. I think I'll probably be ok.
One of your brakes suddenly being torn off the bike can't be that bad right? I bet it'll jam up in the spokes, and therefore still be doing what it was meant for.
HAHAHA.








